中空玻璃设备在日常使用要注意哪些？

1、设备出现异常应立即停车检修，故障排除后再行运转。
1, abnormal equipment should immediately stop maintenance, troubleshooting after the operation.
2、各处轴承和链轮处应定期加住润滑脂和润滑油，减速机6个月加注一次，
2, each place bearing and sprocket should regularly add grease and lubricating oil, reducer once every 6 months,
板压段的导轨及两导轴应经常加注润滑油。
Lubricating oil should be often added to the guide rail and the two guide shaft of the pressure plate.
3、每工作5000小時后，应对角接触球轴承进行清洗，添加NBU-15润滑脂或锂基润滑脂（SY1412-75），添加量为内腔面积的1∕3～2∕3左右，軸承达不到精度时可更换。切记：清洗干燥部分的清洗室不能任何润滑油和非中性液体，避免水源被污染。

3, every 5000 hours of work, should the angular contact ball bearing cleaning, NBU-15 grease or lithium grease additive (SY1412-75), was added to the 1 lumen area / 3 ~ 2 / 3 or so, can not reach the accuracy of bearing replacement. Remember: cleaning the drying part of the cleaning room can not be any lubricating oil and non neutral liquid, to avoid water pollution.

4、经常检查电气线路，有否破损或鼠咬，各接头处有否松动，电控箱内应保持整洁、干燥。
4, often check the electrical circuit, whether damaged or rodent bite, the joints are loose, the electrical control box should be kept clean and dry.
5、每段气缸及其它活动处要经常注入润滑油，电磁阀板应保持清洁，接头可靠
5, each segment of the cylinder and other activities should be regularly injected lubricating oil, solenoid valve plate should be kept clean, reliable joints
6、设备上的灰尘应及时擦净，设备背靠板、背靠轮要保持清洁，每个工作班次要及时清除灰尘和杂质。
6, dust on the equipment should be promptly wiped, equipment back plate, back wheel to keep clean, each work shift should promptly remove dust and impurities.
7、三联体（分水滤气器每班防水，每周清洗一次，压力表调至0.5～0.8mpa,油雾器保持一定油位，机械油（N32#）滴油时调整到每分钟一滴左右。
7, three conjoined (water separator gas filter each class waterproof, cleaning once a week, the pressure gauge is adjusted to 0.5 ~ 0.8MPa, oil mist to maintain a certain oil level, mechanical oil (N32#) drops when the oil is adjusted to about one drop per minute.
8、经常检查螺栓联结处有否松动，若有应及时紧固。
8, often check whether the bolt connection is loose, if there should be timely fastening.
9、设备长时间不用时，应将设备擦净，用塑料布罩好，以防积尘、锈蚀。
9, when the equipment is not used for a long time, the equipment should be cleaned, covered with plastic cloth, in order to prevent dust accumulation, corrosion.
有了铝切割设备上面的小总结，希望对广大客户有所帮助，如果有什么不理解的或者寻求帮助的请点击我们的官方网站：http://www.szwmdjx.com或者来电咨询，我们会尽全力为您解决
A small sum aluminum cutting equipment above, hope to help customers, if what you do not understand or seek help please click on our official website: http://www.szwmdjx.com or contact us, we will do our best for you to solve